机械专业术语英汉对照3

机械专业术语英汉对照

无级变速装置 stepless speed changes devices无穷大 infinite系杆 crank arm, planet carrier 现场平衡 field balancing 向心轴承 radial bearing向心力 centrifugal force相对速度 relative velocity相对运动 relative motion相对间隙 relative gap象限 quadrant橡皮泥 plasticine细牙螺纹 fine threads销 pin消耗 consumption小齿轮 pinion小径 minor diameter橡胶弹簧 balata spring修正梯形加速度运动规律 modified trapezoidal acceleration motion修正正弦加速度运动规律 modified sine acceleration motion斜齿圆柱齿轮 helical gear斜键、钩头楔键 taper key泄漏 leakage谐波齿轮 harmonic gear谐波传动 harmonic driving谐波发生器 harmonic generator斜齿轮的当量直齿轮 equivalent spur gear of the helical gear心轴 spindle行程速度变化系数 coefficient of travel speed variation行程速比系数 advance-to return-time ratio行星齿轮装置 planetary transmission行星轮 planet gear行星轮变速装置 planetary speed changing devices行星轮系 planetary gear train形封闭凸轮机构 positive-drive (or form-closed) cam mechanism虚拟现实 virtual reality虚拟现实技术 virtual reality technology, VRT虚拟现实设计 virtual reality design, VRD虚约束 redundant (or passive) constraint许用不平衡量 allowable amount of unbalance许用压力角 allowable pressure angle许用应力 allowable stress; permissible stress悬臂结构 cantilever structure悬臂梁 cantilever beam循环功率流 circulating power load旋转力矩 running torque旋转式密封 rotating seal旋转运动 rotary motion选型 type selection压力 pressure 压力中心 center of pressure 压缩机 compressor压应力 compressive stress压力角 pressure angle牙嵌式联轴器 jaw (teeth) positive-contact coupling雅可比矩阵 Jacobi matrix摇杆 rocker液力传动 hydrodynamic drive液力耦合器 hydraulic couplers液体弹簧 liquid spring液压无级变速 hydraulic stepless speed changes液压机构 hydraulic mechanism一般化运动链 generalized kinematic chain移动从动件 reciprocating follower移动副 prismatic pair, sliding pair移动关节 prismatic joint移动凸轮 wedge cam盈亏功 increment or decrement work应力幅 stress amplitude应力集中 stress concentration应力集中系数 factor of stress concentration应力图 stress diagram应力 — 应变图 stress-strain diagram优化设计 optimal design油杯 oil bottle油壶 oil can油沟密封 oily ditch seal有害阻力 useless resistance有益阻力 useful resistance有效拉力 effective tension有效圆周力 effective circle force有害阻力 detrimental resistance余弦加速度运动 cosine acceleration (or simple harmonic) motion预紧力 preload原动机 primer mover圆带 round belt圆带传动 round belt drive圆弧齿厚 circular thickness圆弧圆柱蜗杆 hollow flank worm圆角半径 fillet radius圆盘摩擦离合器 disc friction clutch圆盘制动器 disc brake原动机 prime mover原始机构 original mechanism圆形齿轮 circular gear圆柱滚子 cylindrical roller圆柱滚子轴承 cylindrical roller bearing圆柱副 cylindric pair圆柱式凸轮步进运动机构 barrel (cylindric) cam圆柱螺旋拉伸弹簧 cylindroid helical-coil extension spring圆柱螺旋扭转弹簧 cylindroid helical-coil torsion spring圆柱螺旋压缩弹簧 cylindroid helical-coil compression spring圆柱凸轮 cylindrical cam圆柱蜗杆 cylindrical worm圆柱坐标操作器 cylindrical coordinate manipulator圆锥螺旋扭转弹簧 conoid helical-coil compression spring圆锥滚子 tapered roller圆锥滚子轴承 tapered roller bearing圆锥齿轮机构 bevel gears圆锥角 cone angle原动件 driving link约束 constraint约束条件 constraint condition约束反力 constraining force跃度 jerk跃度曲线 jerk diagram运动倒置 kinematic inversion运动方案设计 kinematic precept design运动分析 kinematic analysis运动副 kinematic pair运动构件 moving link运动简图 kinematic sketch运动链 kinematic chain运动失真 undercutting运动设计 kinematic design运动周期 cycle of motion运动综合 kinematic synthesis运转不均匀系数 coefficient of velocity fluctuation运动粘度 kenematic viscosity载荷 load 载荷 — 变形曲线 load—deformation curve 载荷 — 变形图 load—deformation diagram窄 V 带 narrow V belt毡圈密封 felt ring seal展成法 generating张紧力 tension张紧轮 tension pulley振动 vibration振动力矩 shaking couple振动频率 frequency of vibration振幅 amplitude of vibration正切机构 tangent mechanism正向运动学 direct (forward) kinematics正弦机构 sine generator, scotch yoke织布机 loom正应力、法向应力 normal stress制动器 brake直齿圆柱齿轮 spur gear直齿锥齿轮 straight bevel gear直角三角形 right triangle直角坐标操作器 Cartesian coordinate manipulator直径系数 diametral quotient直径系列 diameter series直廓环面蜗杆 hindley worm直线运动 linear motion直轴 straight shaft质量 mass质心 center of mass执行构件 executive link; working link质径积 mass-radius product智能化设计 intelligent design, ID中间平面 mid-plane中心距 center distance中心距变动 center distance change中心轮 central gear中径 mean diameter终止啮合点 final contact, end of contact周节 pitch周期性速度波动 periodic speed fluctuation周转轮系 epicyclic gear train肘形机构 toggle mechanism轴 shaft轴承盖 bearing cup轴承合金 bearing alloy轴承座 bearing block轴承高度 bearing height轴承宽度 bearing width轴承内径 bearing bore diameter轴承寿命 bearing life轴承套圈 bearing ring轴承外径 bearing outside diameter轴颈 journal轴瓦、轴承衬 bearing bush轴端挡圈 shaft end ring轴环 shaft collar轴肩 shaft shoulder轴角 shaft angle轴向 axial direction轴向齿廓 axial tooth profile轴向当量动载荷 dynamic equivalent axial load轴向当量静载荷 static equivalent axial load轴向基本额定动载荷 basic dynamic axial load rating轴向基本额定静载荷 basic static axial load rating轴向接触轴承 axial contact bearing轴向平面 axial plane轴向游隙 axial internal clearance轴向载荷 axial load轴向载荷系数 axial load factor轴向分力 axial thrust load主动件 driving link主动齿轮 driving gear主动带轮 driving pulley转动导杆机构 whitworth mechanism转动副 revolute (turning) pair转速 swiveling speed rotating speed转动关节 revolute joint转轴 revolving shaft转子 rotor转子平衡 balance of rotor装配条件 assembly condition锥齿轮 bevel gear锥顶 common apex of cone锥距 cone distance锥轮 bevel pulley; bevel wheel锥齿轮的当量直齿轮 equivalent spur gear of the bevel gear锥面包络圆柱蜗杆 milled helicoids worm准双曲面齿轮 hypoid gear子程序 subroutine子机构 sub-mechanism自动化 automation自锁 self-locking自锁条件 condition of self-locking自由度 degree of freedom, mobility总重合度 total contact ratio总反力 resultant force总效率 combined efficiency; overall efficiency组成原理 theory of constitution组合齿形 composite tooth form组合安装 stack mounting组合机构 combined mechanism阻抗力 resistance最大盈亏功 maximum difference work between plus and minus work纵向重合度 overlap contact ratio纵坐标 ordinate组合机构 combined mechanism最少齿数 minimum teeth number最小向径 minimum radius作用力 applied force坐标系 coordinate frame
3D coordinate measurement 三次元量床 boring machine 搪孔机 cnc milling machine CNC铣床 contouring machine 轮廓锯床 copy grinding machine 仿形磨床 copy lathe 仿形车床 copy milling machine 仿形铣床 copy shaping machine 仿形刨床 cylindrical grinding machine 外圆磨床 die spotting machine 合模机 drilling machine ?孔机 engraving machine 雕刻机 engraving E.D.M. 雕模放置加工机 form grinding machine 成形磨床 graphite machine 石墨加工机 horizontal boring machine 卧式搪孔机 horizontal machine center 卧式加工制造中心 internal cylindrical machine 内圆磨床 jig boring machine 冶具搪孔机 jig grinding machine 冶具磨床 lap machine 研磨机 machine center 加工制造中心 multi model miller 靠磨铣床 NC drilling machine NC钻床 NC grinding machine NC磨床 NC lathe NC车床 NC programming system NC程式制作系统 planer 龙门刨床 profile grinding machine 投影磨床 projection grinder 投影磨床 radial drilling machine 旋臂?床 shaper 牛头刨床 surface grinder 平面磨床 try machine 试模机 turret lathe 转塔车床 universal tool grinding machine 万能工具磨床 vertical machine center 立式加工制造中心 wire E.D.M. 线割放电加工机
barrel 滚筒(加工) bending 波纹加工 broaching 拉刀切削 centering 定中心 cutting 切削 cylindrical lathe cutting 外圆车削 electric discharge machine 放电加工 electrolytic grinding 电解研磨 embossing 压花加工 facing 面车削 filing 锉刀修润 hand finishing 手工修润 hemming 卷边加工 hobbing 滚齿加工 joggling 摇动加工 lapping 抛光/研磨修润 laser beam machining 雷射加工 lathe cutting 车床车削 planning 刨削加工 polishing 抛亮光 reaming 铰孔修润 rough machining 粗切削 rounding 圆形加工 sawing 锯削 scaling 清除钢碇缺陷 shaping 成形加工 skiving 表面研磨 slotting 切缝切削 taper turning 锥度车削 thread cutting 螺纹切削 ultrasonic machining 超音波加工 up cut milling 逆铣加工
alloy tool steel 合金工具钢 aluminium alloy 铝合金钢 bearing alloy 轴承合金 blister steel 浸碳钢 bonderized steel sheet 邦德防蚀钢板 carbon tool steel 碳素工具钢 clad sheet 被覆板 clod work die steel 冷锻模用钢 emery 金钢砂 ferrostatic pressure 钢铁水静压力 forging die steel 锻造模用钢 galvanized steel sheet 镀锌铁板 hard alloy steel 超硬合金钢 high speed tool steel 高速度工具钢 hot work die steel 热锻模用钢 low alloy tool steel 特殊工具钢 low manganese casting steel 低锰铸钢 marging steel 马式体高强度热处理钢 martrix alloy 马特里斯合金 meehanite cast iron 米汉纳铸钢 meehanite metal 米汉纳铁 merchant iron 市售钢材 molybdenum high speed steel 钼系高速钢 molybdenum steel 钼钢 nickel chromium steel 镍铬钢 prehardened steel 顶硬钢 silicon steel sheet 矽钢板 stainless steel 不锈钢 tin plated steel sheet 镀锡铁板 tough pitch copper 韧铜 troostite 吐粒散铁 tungsten steel ?钢 vinyl tapped steel sheet 塑胶覆面钢板
acetylene 乙炔 ampere 电流安培 angle welding 角焊 arc 电弧 argon arc welding 氩弧焊接 bare electrode 光熔接条 butt welding 对接焊接 camber 电弧弯曲 cascade 阶叠熔接法 clad weld 被覆熔接 crator 焊疤 excess metal 多余金属 filler rod 焊条 fillet weld 填角焊接 gas shield 气体遮蔽 groove welding 起槽熔接 hand face shield 手握面罩 hard facing 硬表面堆焊 jig welding 工模焊接 laser beam welding 雷射光焊接 metal electrode insert gas welding MIG熔接 nugget 点焊熔核 overlaying 堆焊 peening of welding 珠击熔接法 plug welding 塞孔熔接 positioned welding 正向熔接 pressure welding 压焊 propane gas cutting 丙烷气切割 pure nickel electrode 纯镍熔接条 reinforcement of weld 加强焊接 resist 抗蚀护膜 root running 背面熔接 seam 焊缝 seaming 接合 seam welding 流缝熔接 series seam welding 串联缝熔接 skip welding process 跳焊法 spark 火花 spot welding 点焊接 stitch welding 针角焊接 stud arc welding 电弧焊接 under laying 下部焊层 void 焊接空隙 weld flow mark 焊接流痕 weld flush 焊缝凸起 weld line 焊接纹 weld mark 焊接痕 weld penetration 熔接透入 weld zone 焊接区 welding 焊接 welding bead 焊接泡 welding direction 焊接方向 welding distortion 焊接变形 welding flux 焊剂 welding ground 电熔接地 welding interval 焊接周期 welding stress 熔接应变 welding torch 熔接气炬
molding成型 spare parts=buffer备品 coordinate座标 dismantle the die折模 auxiliary fuction辅助功能 poly-line多义线 heater band 加热片 thermocouple热电偶 sand blasting喷沙 grit 砂砾 derusting machine除锈机 degate打浇口 dryer烘干机 induction感应 induction light感应光response=reaction=interaction感应 ram连杆 edge finder巡边器 concave凸 convex凹 short射料不足 nick缺口 speck瑕?? shine亮班 splay 银纹 gas mark焦痕 delamination起鳞 cold slug冷块 blush 导色 gouge沟槽;凿槽 satin texture段面咬花 witness line证示线 patent专利 grit沙砾 granule=peuet=grain细粒 grit maker抽粒机 cushion缓冲 magnalium镁铝合金 magnesium镁金 metal plate钣金 lathe车 mill锉 plane刨 grind磨 drill铝 boring镗 blinster气泡 fillet镶;嵌边 through-hole form通孔形式 voller pin formality滚针形式 cam driver铡楔 shank摸柄 crank shaft曲柄轴 augular offset角度偏差 velocity速度production tempo生产进度现状 torque扭矩 spline=the multiple keys花键 quenching淬火 tempering回火 annealing退火 carbonization碳化 tungsten high speed steel钨高速的 moly high speed steel钼高速的 organic solvent有机溶剂 bracket小磁导 liaison联络单 volatile挥发性 resistance电阻 ion离子 titrator滴定仪 beacon警示灯 coolant冷却液 crusher破碎机
点 dot 点阵间距；点阵间隔 lattice spacing 点焊接 spot welding 醛树脂；电玉 ureaformaldehyde (UF) 十八画 断面线 cross hatching line 断裂 fracture 断路掣 miniature circuit breaker (MCB) 柜 carcase 台夹；固定夹 bench holdfast 台阻 bench stop 台垫；垫板 bench hook 簧片 spring 简单齿轮系 simple gear train 简谐运动 simple harmonic motion 廿三画 纤维 fibre 纤维板 fibre board 纤维素醋酸酯 cellulose acetate (CA) 变形；扭曲 distortion 变速系统 speed control system 变压器；火牛 transformer 逻辑状态 logic state 逻辑门 logic gate 髓线 medullary ray 体积 volume 鹬嘴钳 snipe nose pliers 廿四画 灵敏度 sensitivity 廿五画 镶边 lipping 廿六画 钻 drill 钻孔；钻削 drill; drilling 钻床 drilling machine 钻嘴 bit 钻头夹盘 drill chuck 钻头扳手 drill chuck key 凿 chisel 凿切 chiselling 凿身 chisel blade 其它 G 字夹 G clamp G 码 G code M 码 M code PN 结 PN junction PVC 胶；聚氯乙烯 polyvinyl chloride (PVC) T 尺；丁字尺 tee square T 字叉榫 tee bridle joint T 角榫 tee angle joint T 型接合 tee joint V 字板 V-board V 形坑带和滑轮 vee belt and pulley V 形枕 V block V 型槽座与钳 vee block & clamp
Assembly line组装线 Layout布置图 Conveyer流水线物料板 Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子 Electric screw driver电动起子 Pneumatic screw driver气动起子 worktable 工作桌 OOBA开箱检查 fit together组装在一起 fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板 barcode条码 barcode scanner条码扫描器 fuse together熔合 fuse machine热熔机 repair修理 operator作业员 QC品管 supervisor 课长 ME制造工程师 MT制造生技 cosmetic inspect外观检查 inner parts inspect内部检查 thumb screw大头螺丝 lbs. inch镑、英寸 EMI gasket导电条 front plate前板 rear plate后板 chassis 基座 bezel panel面板 power button电源按键 reset button重置键 Hi-pot test of SPS高源高压测试 Voltage switch of SPS 电源电压接拉键 sheet metal parts 冲件 plastic parts塑胶件 SOP制造作业程序 material check list物料检查表 work cell工作间 trolley台车 carton纸箱 sub-line支线 left fork叉车 production department生产部门 planning department企划部 QC Section品管科 stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 common equipment常用设备 uncoiler and straightener整平机 punching machine 冲床 robot机械手 hydraulic machine油压机 lathe车床 planer |'plein?|刨床 miller铣床 grinder磨床 driller铣床 linear cutting线切割 electrical sparkle电火花 welder电焊机 staker=reviting machine铆合机 position职务 president董事长 general manager总经理 special assistant manager特助 factory director厂长 department director部长 deputy manager | =vice manager副理 section supervisor课长 deputy section supervisor =vice section superisor副课长 group leader/supervisor组长 line supervisor线长 assistant manager助理 to move, to carry, to handle搬运 be put in storage入库 pack packing包装 to apply oil擦油 to file burr 锉毛刺 final inspection终检 to connect material接料 to reverse material 翻料 wet station沾湿台 Tiana天那水 cleaning cloth抹布 to load material上料 to unload material卸料 to return material/stock to退料 scraped |'skr?pid|报废 scrape ..v.刮;削 deficient purchase来料不良 manufacture procedure制程 deficient manufacturing procedure制程不良 oxidation |' ksi'dei?n|氧化 scratch刮伤 dents压痕 defective upsiding down抽芽不良 defective to staking铆合不良 embedded lump镶块 feeding is not in place送料不到位 stamping-missing漏冲 production capacity生产力 education and training教育与训练 proposal improvement提案改善 spare parts=buffer备件 forklift叉车 trailer=long vehicle拖板车 compound die合模 die locker锁模器 pressure plate=plate pinch压板 bolt螺栓 name of a department部门名称 administration/general affairs dept总务部 automatic screwdriver电动启子 thickness gauge厚薄规 gauge(or jig)治具 power wire电源线 buzzle蜂鸣器 defective product label不良标签 identifying sheet list标示单 screwdriver holder起子插座 pedal踩踏板 stopper阻挡器 flow board流水板 hydraulic handjack油压板车 forklift叉车 pallet栈板 glove(s)手套 glove(s) with exposed fingers割手套 thumb大拇指 forefinger食指 midfinger中指 ring finger无名指 little finger小指 band-aid创可贴 iudustrial alcohol工业酒精 alcohol container沾湿台 head of screwdriver起子头 sweeper扫把 mop拖把 vaccum cleaner吸尘器 rag 抹布 garbage container灰箕 garbage can垃圾箱 garbage bag垃圾袋 chain链条 jack升降机 production line流水线 chain链条槽 magnetizer加磁器 lamp holder灯架 to mop the floor拖地 to clean the floor扫地 to clean a table擦桌子 air pipe 气管 packaging tool打包机 packaging打包 missing part漏件 wrong part错件 excessive defects过多的缺陷 critical defect极严重缺陷 major defect主要缺陷 minor defect次要缺陷 not up to standard不合规格 dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良 slipped screwhead/slippery screw head螺丝滑头 slipped screwhead/shippery screw thread滑手 speckle斑点 mildewed=moldy=mouldy发霉 rust生锈 deformation变形 burr(金属)flash(塑件)毛边 poor staking铆合不良 excesssive gap间隙过大 grease/oil stains油污 inclusion杂质 painting peel off脏污 shrinking/shrinkage缩水 mixed color杂色 scratch划伤 poor processing 制程不良 poor incoming part事件不良 fold of pakaging belt打包带折皱 painting make-up补漆 discoloration羿色 water spots水渍 polishing/surface processing表面处理 exposed metal/bare metal金属裸露 lack of painting烤漆不到位 safety安全 quality品质 delivery deadline交货期 cost成本 engineering工程 die repair模修 enterprise plan = enterprise expansion projects企划 QC品管 die worker模工 production, to produce生产 equipment设备 to start a press开机 stop/switch off a press关机 classification整理 regulation整顿 cleanness清扫 conservation清洁 culture教养 qualified products, up-to-grade products良品 defective products, not up-to-grade products不良品 waste废料 board看板 feeder送料机 sliding rack滑料架 defective product box不良品箱 die change 换模 to fix a die装模 to take apart a die拆模 to repair a die修模 packing material包材 basket蝴蝶竺 plastic basket胶筐 isolating plate baffle plate; barricade隔板 carton box纸箱 to pull and stretch拉深 to put material in place, to cut material, to input落料 to impose lines压线 to compress, compressing压缩 character die字模 to feed, feeding送料 transportation运输 (be)qualfied, up to grade合格 not up to grade, not qualified不合格 material change, stock change材料变更 feature change 特性变更 evaluation评估 prepare for, make preparations for 准备 parameters参数 rotating speed, revolution转速 manufacture management制造管理 abnormal handling异常处理 production unit生产单位 lots of production生产批量 steel plate钢板 roll material卷料 manufacture procedure制程 operation procedure作业流程 to revise, modify修订 to switch over to, switch---to throw--over switching over切换 engineering, project difficulty 工程瓶颈 stage die工程模 automation自动化 to stake, staking, reviting铆合 add lubricating oil加润滑油 shut die架模 shut height of a die架模高度 analog-mode device类模器 die lifter举模器 argon welding氩焊 vocabulary for stamping 冲压常词汇 stamping, press冲压 punch press, dieing out press冲床 uncoiler & strainghtener整平机 feeder送料机 rack, shelf, stack料架 cylinder油缸 robot机械手 taker取料机 conveyer belt输送带 transmission rack输送架 top stop上死点 bottom stop下死点 one stroke一行程 inch寸动 to continue, cont.连动 to grip(material)吸料 location lump, locating piece, block stop 定位块 reset复位 smoothly顺利 dent压痕 scratch刮伤 deformation变形 filings铁削 to draw holes抽孔 inquiry, search for查寻 to stock, storage, in stock库存 receive领取 approval examine and verify审核 processing, to process加工 delivery, to deliver 交货 to return delivenry to. to send delinery back to retrn of goods退货 registration登记 registration card登记卡 to control管制 to put forward and hand in提报 safe stock安全库存 acceptance = receive验收 to notice通知 application form for purchase请购单 consume, consumption消耗 to fill in填写 abrasion磨损 reverse angle = chamfer倒角 character die字模 to collect, to gather收集 failure, trouble故障 statistics统计 demand and supply需求 career card履历卡 to take apart a die卸下模具 to load a die装上模具 to tight a bolt拧紧螺栓 to looser a bolt拧松螺栓 to move away a die plate移走模板 easily damaged parts易损件 standard parts标准件 breaking.(be)broken,(be)cracked 断裂 to lubricate润滑 common vocabulary for die engineering 模具工程常用词汇 die 模具 figure file, chart file图档 cutting die, blanking die冲裁模 progressive die, follow (-on)die 连续模 compound die复合模 punched hole冲孔 panel board镶块 to cutedges=side cut=side scrap切边 to bending折弯 to pull, to stretch拉伸 Line streching, line pulling线拉伸 engraving, to engrave刻印 upsiding down edges翻边 to stake铆合 designing, to design设计 design modification设计变化 die block模块 folded block折弯块 sliding block滑块 location pin定位销 lifting pin顶料销 die plate, front board模板 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓 document folder文件夹 file folder资料夹 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count 复盘人 second check复盘复核人 equipment设备 waste materials废料 work in progress product在制品 casing = containerazation装箱 quantity of physical invetory second count 复盘点数量 quantity of customs count 会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位 summary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name单据名称 This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表 blank and waste sheet NO. 空白与作废单号 plate电镀 mold成型 material for engineering mold testing工程试模材料 not included in physical inventory不列入盘点 sample样品 incoming material to be inspected进货待验 description品名 steel/rolled steel钢材 material statistics sheet 物料统计明细表 meeting minutes会议记录 meeting type 会别 distribution department分发单位 location地点 chairman主席 present members出席人员 subject主题 conclusion结论 decision items决议事项 responsible department负责单位 pre-fixed finishing date预定完成日 approved by / checked by / prepared by核准/审核/承办 PCE assembly production schedule sheet PCE组装厂生产排配表 model机锺 work order工令 revision版次 remark备注 production control confirmation生产确认 checked by初审 approved by核准 department部门 stock age analysis sheet 库存货龄分析表 on-hand inventory现有库存 available material良品可使用 obsolete material良品已呆滞 to be inspected or reworked 待验或重工 total合计 cause description原因说明 part number/ P/N 料号 type形态 item/group/class类别 quality品质 prepared by制表 notes说明 year-end physical inventory difference analysis sheet 年终盘点差异分析表 physical inventory盘点数量 physical count quantity帐面数量 difference quantity差异量 cause analysis原因分析 raw materials原料 materials物料 finished product成品 semi-finished product半成品 packing materials包材 good product/accepted goods/ accepted parts/good parts良品 defective product/non-good parts不良品 disposed goods处理品 warehouse/hub仓库 on way location在途仓 oversea location海外仓 spare parts physical inventory list备品盘点清单 spare molds location模具备品仓 skid/pallet栈板 tox machine自铆机 wire EDM线割 EDM放电机 coil stock卷料 sheet stock片料 tolerance工差 score=groove压线 cam block滑块 pilot导正筒 trim剪外边 pierce剪内边 drag form压锻差 pocket for the punch head挂钩槽 slug hole废料孔 feature die公母模 expansion dwg展开图 radius半径 shim(wedge)楔子 torch-flame cut火焰切割 set screw止付螺丝 form block折刀 stop pin定位销 round pierce punch=die button圆冲子 shape punch=die insert异形子 stock locater block定位块 under cut=scrap chopper清角 active plate活动板 baffle plate挡块 cover plate盖板 male die公模 female die母模 groove punch压线冲子 air-cushion eject-rod气垫顶杆 spring-box eject-plate弹簧箱顶板 bushing block衬套 insert 入块 club car高尔夫球车 capability能力 parameter参数 factor系数 phosphate皮膜化成 viscosity涂料粘度 alkalidipping脱脂 main manifold主集流脉 bezel斜视规 blanking穿落模 dejecting顶固模 demagnetization去磁;消磁 high-speed transmission高速传递 heat dissipation热传 rack上料 degrease脱脂 rinse水洗 alkaline etch龄咬 desmut剥黑膜 D.I. rinse纯水次 Chromate铬酸处理 Anodize阳性处理 seal封孔 revision版次 part number/P/N料号 good products良品 scraped products报放心品 defective products不良品 finished products成品 disposed products处理品 barcode条码 flow chart流程表单 assembly组装 stamping冲压 molding成型 spare parts=buffer备品 coordinate座标 dismantle the die折模 auxiliary fuction辅助功能 poly-line多义线 heater band 加热片 thermocouple热电偶 sand blasting喷沙 grit 砂砾 derusting machine除锈机 degate打浇口 dryer烘干机 induction感应 induction light感应光 response=reaction=interaction感应 ram连杆 edge finder巡边器 concave凸 convex凹 short射料不足 nick缺口 speck瑕?? shine亮班 splay 银纹 gas mark焦痕 delamination起鳞 cold slug冷块 blush 导色 gouge沟槽;凿槽 satin texture段面咬花 witness line证示线 patent专利 grit沙砾 granule=peuet=grain细粒 grit maker抽粒机 cushion缓冲 magnalium镁铝合金 magnesium镁金 metal plate钣金 lathe车 mill锉 plane刨 grind磨 drill铝 boring镗 blinster气泡 fillet镶;嵌边 through-hole form通孔形式 voller pin formality滚针形式 cam driver铡楔 shank摸柄 crank shaft曲柄轴 augular offset角度偏差 velocity速度 production tempo生产进度现状 torque扭矩 spline=the multiple keys花键 quenching淬火 tempering回火 annealing退火 carbonization碳化 alloy合金 tungsten high speed steel钨高速的 moly high speed steel钼高速的 organic solvent有机溶剂 bracket小磁导 liaison联络单 volatile挥发性 resistance电阻 ion离子 titrator滴定仪 beacon警示灯 coolant冷却液 crusher破碎机 模具工程类 plain die简易模 pierce die冲孔模 forming die成型模 progressive die连续模 gang dies复合模 shearing die剪边模 riveting die铆合模 pierce冲孔 forming成型(抽凸,冲凸) draw hole抽孔 bending折弯 trim切边 emboss凸点 dome凸圆 semi-shearing半剪 stamp mark冲记号 deburr or coin压毛边 punch riveting冲压铆合 side stretch侧冲压平 reel stretch卷圆压平 groove压线 blanking下料 stamp letter冲字(料号) shearing剪断 tick-mark nearside正面压印 tick-mark farside反面压印 冲压名称类 extension dwg展开图 procedure dwg工程图 die structure dwg模具结构图 material材质 material thickness料片厚度 factor系数 upward向上 downward向下 press specification冲床规格 die height range适用模高 die height闭模高度 burr毛边 gap间隙 weight重量 total wt.总重量 punch wt.上模重量 五金零件类 inner guiding post内导柱 inner hexagon screw内六角螺钉 dowel pin固定销 coil spring弹簧 lifter pin顶料销 eq-height sleeves=spool等高套筒 pin销 lifter guide pin浮升导料销 guide pin导正销 wire spring圆线弹簧 outer guiding post外导柱 stop screw止付螺丝 located pin定位销 outer bush外导套 模板类 top plate上托板（顶板） top block上垫脚 punch set上模座 punch pad上垫板 punch holder上夹板 stripper pad脱料背板 up stripper上脱料板 male die公模(凸模) feature die公母模 female die母模(凹模) upper plate上模板 lower plate下模板 die pad下垫板 die holder下夹板 die set下模座 bottom block下垫脚 bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板 inner stripper内脱料板 lower stripper下脱料板 零件类 punch冲头 insert入块(嵌入件) deburring punch压毛边冲子 groove punch压线冲子 stamped punch字模冲子 round punch圆冲子 special shape punch异形冲子 bending block折刀 roller滚轴 baffle plate挡块 located block定位块 supporting block for location 定位支承块 air cushion plate气垫板 air-cushion eject-rod气垫顶杆 trimming punch切边冲子 stiffening rib punch = stinger 加强筋冲子 ribbon punch压筋冲子 reel-stretch punch卷圆压平冲子 guide plate定位板 sliding block滑块 sliding dowel block滑块固定块 active plate活动板 lower sliding plate下滑块板 upper holder block上压块 upper mid plate上中间板 spring box弹簧箱 spring-box eject-rod弹簧箱顶杆 spring-box eject-plate弹簧箱顶板 bushing bolck衬套 cover plate盖板 guide pad导料块 塑件&模具相关英文 compre sion molding压缩成型 flash mold溢流式模具 plsitive mold挤压式模具 split mold分割式模具 cavity型控 母模 core模心 公模 taper锥拔 leather cloak仿皮革 shiver饰纹 flow mark流痕 welding mark溶合痕 post screw insert螺纹套筒埋值 self tapping screw自攻螺丝 striper plate脱料板 piston活塞 cylinder汽缸套 chip细碎物 handle mold手持式模具 移转成型用模具 encapsulation molding低压封装成型 射出成型用模具 two plate两极式（模具） well type蓄料井 insulated runner绝缘浇道方式 hot runner热浇道 runner plat浇道模块 valve gate阀门浇口 band heater环带状的电热器 spindle阀针 spear head刨尖头 slag well冷料井 cold slag冷料渣 air vent排气道 h=0.02~0.05mm w=3.2mm L=3~5mm welding line熔合痕 eject pin顶出针 knock pin顶出销 return pin回位销反顶针 sleave套筒 stripper plate脱料板 insert core放置入子 runner stripper plate浇道脱料板 guide pin导销 eject rod (bar)（成型机）顶业捧 subzero深冷处理 three plate三极式模具 runner system浇道系统 stress crack应力电裂 orientation定向 sprue gate射料浇口，直浇口 nozzle射嘴 sprue lock pin料头钩销(拉料杆) slag well冷料井 side gate侧浇口 edge gate侧缘浇口 tab gate搭接浇口 film gate薄膜浇口 flash gate闸门浇口 slit gate缝隙浇口 fan gate扇形浇口 dish gate因盘形浇口 H=F=1/2t~1/5t T=2.5~3.5mm diaphragm gate隔膜浇口 ring gate环形浇口 subarine gate潜入式浇口 tunnel gate隧道式浇口 pin gate针点浇口 Φ0.8~1.0mm Runner less无浇道 (sprue less)无射料管方式 long nozzle延长喷嘴方式 sprue浇口;溶渣
品质人员名称类 QC quality control 品质管理人员 FQC final quality control 终点品质管制人员 IPQC in process quality control 制程中的品质管制人员 OQC output quality control 最终出货品质管制人员 IQC incoming quality control 进料品质管制人员 TQC total quality control 全面质量管理 POC passage quality control 段检人员 QA quality assurance 质量保证人员 OQA output quality assurance 出货质量保证人员 QE quality engineering 品质工程人员 品质保证类 FAI first article inspection 新品首件检查 FAA first article assurance 首件确认 TVR tool verification report 模具确认报告 3B 3B 模具正式投产前确认 CP capability index 能力指数 CPK capability index of process 模具制程能力参数 SSQA standardized supplier quality 合格供应商品质评估 OOBA out of box audit 开箱检查 QFD quality function deployment 品质机能展开 FMEA failure model effectiveness analysis 失效模式分析 8 disciplines 8项回复内容 FA final audit 最後一次稽核 CAR corrective action request 改正行动要求 corrective action report 改正行动报告 FQC运作类 AQL Acceptable Quality Level 运作类允收品质水准 S/S Sample size 抽样检验样本大小 ACC Accept 允收 REE Reject 拒收 CR Critical 极严重的 MAJ Major 主要的 MIN Minor 轻微的 AOQ Average Output Quality 平均出厂品质 AOQL Average Output Quality Level 平均出厂品质 Q/R/S Quality/Reliability/Service 品质/可靠度服务 MIL-STD Military-Standard 军用标准 S I-S IV Special I-Special IV 特殊抽样水准等级 P/N Part Number 料号 L/N Lot Number 特采 AOD Accept On Deviation 特采 UAI Use As It 首件检查报告 FPIR First Piece Inspection Report 百万分之一 PPM Percent Per Million 批号 制程统计品管专类 SPC Statistical Process Control 统计制程管制 SQC Statistical Quality Control 统计品质管制 R Range 全距 AR Averary Range 全距平均值 UCL Upper Central Limit 管制上限 LCL Lower Central Limit 管制下限 MAX Maximum 最大值 MIN Minimum 最小值 GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否 DIM Dimension 尺寸 DIA Diameter 直径 FREQ Frequency 频率 N Number 样品数 其它品质术语类 QCC Quality Control Circle 品质圈 QIT Quality Improvement Team 品质改善小组 PDCA Plan Do Check Action 计划 执行 检查 总结 ZD Zero Defect 零缺点 QI Quality Improvement 品质改善 QP Quality Policy 目标方针 TQM Total Quality Management 全面品质管理 MRB Material Reject Bill 退货单 LQL Limiting Quality Level 最低品质水准 RMA Return Material Audit 退料认可 QAN Quality Amelionrate Notice 品质改善活动 ADM Absolute Dimension Measuremat 全尺寸测量 QT Quality Target 品质目标 7QCTools 7 Quality Controll Tools 品管七大手法 通用之件类 ECN Engineering Change Notes 工程变更通知(供应商) ECO Engineering Change Order 工程改动要求(客户) PCN Process Change Notice 工序改动通知 PMP Product Management Plan 生产管制计划 SIP Specification In Process 制程检验规格 SOP Standard Operation Procedure 制造作业规范 IS Inspection Specification 成品检验规范 BOM Bill Of Material 物料清单 PS Package Specification 包装规范 SPEC Specification 规格 DWG Drawing 图面 系统文件类 QC Quality System 品质系统 ES Engineering Standarization 工程标准 CGOO China General PCE龙华厂文件 H Huston (美国)休斯敦 C Compaq (美国)康伯公司 C China 中国大陆 A Assembly 组装(厂) S Stamping 冲压(厂) P Painting 烤漆(厂) I Intel 英特尔公司 T TAIWAN 台湾 IWS International Workman Standard 工艺标准 ISO International Standard Organization 国际标准化组织 GS General Specification 一般规格 CMCS C-China M-Manufact C-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范 CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范 CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范 部类 PMC Production & Material Control 生产和物料控制 PPC Production Plan Control 生产计划控制 MC Material Control 物料控制 ME Manafacture Engineering 制造工程部 PE Project Engineering 产品工程部 A/C Accountant Dept 会计部 P/A Personal & Administration 人事行政部 DC Document Center 资料中心 QE Quality Engineering 品质工程(部) QA Quality Assurance 品质保证(处) QC Quality Control 品质管制(课) PD Product Department 生产部 LAB Labratry 实验室 IE Industrial Engineering 工业工程 R&D Research & Design 设计开发部 P Painting 烤漆(厂) A Asssembly 组装(厂) S Stamping 冲压(厂) 生产类 PCS Pieces 个(根,块等) PRS Pairs 双(对等) CTN Carton 卡通箱 PAL Pallet/skid 栈板 PO Purchasing Order 采购订单 MO Manufacture Order 生产单 D/C Date Code 生产日期码 ID/C Identification Code (供应商)识别码 SWR Special Work Request 特殊工作需求 L/N Lot Number 批号 P/N Part Number 料号 其它 OEM Original Equipment Manufacture 原设备制造 PCE Personal Computer Enclosure 个人电脑外设 PC Personal Computer 个人电脑 CPU Central Processing Unit 中央处理器 SECC SECC` 电解片 SGCC SGCC 热浸镀锌材料 NHK North of Hongkong 中国大陆 PRC People's Republic of China 中国大陆 U.S.A the United States of America 美国 A.S.A.P As Soon As Possible 尽可能快的 E-MAIL Electrical-Mail 电子邮件 N/A Not Applicable 不适用 QTY Quantity 数量 VS 以及 REV Revision 版本 JIT Just In Time 零库存 I/O Input/Output 输入/输出 OK Ok 好 NG Not Good 不行,不合格 C=0 Critical=0 极严重不允许 ESD Electry-static Discharge 静电排放 5S 希腊语 整理,整顿,清扫,清洁,教养 ATIN Attention 知会 CC Carbon Copy 副本复印相关人员 APP Approve 核准,认可,承认 CHK Check 确认 AM Ante Meridian 上午 PM Post Meridian 下午 CD Compact Disk 光碟 CD-ROM Compact Disk Read-Only Memory 只读光碟 FDD Floppy Disk Drive 软碟机 HDD Hard Disk Drive 碟碟机 REF Reference 仅供参考 CONN Connector 连接器 CAV Cavity 模穴 CAD Computer Aid Design 计算机辅助设计 ASS'Y Assembly 装配,组装 MAT'S Material 材料 IC Integrated Circuit 集成电路 T/P True Position 真位度 TYP Type 类型 WDR Weekly Delivery Requitement 周出货需求 C?T Cycle Time 制程周期 L/T Lead Time 前置时间(生产前准备时间) S/T Standard Time 标准时间 P/M Product Market 产品市场 3C Computer,Commumcation,Consumer electronic's 消费性电子 5WIH When,Where,Who,What,Why,How to 5M Man,Machine,Material,Method,Measurement 4MIH Man,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略品质保证 DQA Desigh Quality Assurance 设计品质保证 MQA Manufacture Quality Assurance 制造品质保证 SSQA Sales and service Quality Assurance 销售及服务品质保证 LRR Lot Rejeet Rate 批退率 BS Brain storming 脑力激荡 EMI Electronic Magnetion Inspect 高磁测试 FMI Frequency Modulatim Inspect 高频测试 B/M Boar/Molding(flat cable) C/P Connector of PC A/P Assembly SPS Switching power supply 电源箱 DT Desk Top 卧式(机箱) MT Mini-Tower 立式(机箱) DVD Digital Vedio Disk VCD Vdeio Compact Disk LCD Liquid Crystal Display CAD Computer AID Design CAM Computer AID Manufacturing CAE Computer AID Engineering ABIOS Achanced Basic in put/output system 先进的基本输入/输出系统 CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体 PDA Personal Digital Assistant 个人数字助理 IC Integrated Circuit 集成电路 ISA Industry Standard Architecture 工业标准体制结构 MCA Micro Channel Architecture 微通道结构 EISA Extended Industry Standard Architecture 扩充的工业标准结构 SIMM Single in-line memory module 单项导通汇流组件 DIMM Dual in-line Memory Module 双项导通汇流组件 LED Light-Emitting Diode 发光二级管 FMEA Failure Mode Effectivenes 失效模式分析 W/H Wire Harness 金属线绪束集组件 F/C Flat Calle 排线 PCB Printed Circuit Board 印刷电路板 CAR Correction Action Report 改善报告 NG Not Good 不良 WPR Weekly Delivery Requirement 周出货要求 PPM Parts Per Million 百万分之一 TPM Total Production Maintenance 全面生产保养 MRP Material Requiremcnt Planning 物料需计划 OC Operation System 作业系统 TBA To Be Design 待定,定缺 D/C Drawing Change P/P Plans & Procedune EMI Electrical-Music Industry 电子音乐工业 RFI Read Frequency Input 读频输入 MMC Maximum Material Condition MMS Maximum Material Size LMC Least Material Condition LMS Least Material Size

声明：本网站所收集的部分公开资料来源于互联网，转载的目的在于传递更多信息及用于网络分享，并不代表本站赞同其观点和对其真实性负责，也不构成任何其他建议。本站部分作品是由网友自主投稿和发布、编辑整理上传，对此类作品本站仅提供交流平台，不为其版权负责。如果您发现网站上所用视频、图片、文字如涉及作品版权问题，请第一时间告知，我们将根据您提供的证明材料确认版权并按国家标准支付稿酬或立即删除内容，以保证您的权益！联系电话：010-58612588 或 Email:editor@mmsonline.com.cn。